 |
 |
 |
|
Overview:FMA Cellpro Multi4 Charger: Built on the success of the Cellpro 4s and Cellpro 10s chargers, the Cellpro Multi4 represents the next step forward in charging technology. So much more than just another charger, the Multi4 is based on FMA's time-proven, reliable hardware designs and safety algorithms, but sports a new micro-controller that is 4 times as powerful as the one used in the Cellpro 4s. But the true power of the charger stems from totally new firmware. We started with a clean sheet of paper and a lot of "thinking outside the box". The extensive list of features and capabilities are rivaled only by the goal to provide the ultimate in flexibility and utility. Out of the box, the Multi4 will run circles around the competition in terms of simple, yet powerful set up and operation. But if you are the type of person who likes a more custom solution, look no further. The charger, in combination with the Charge Control Software will offer virtually unlimited access to charging parameters. You will need:Appropriate Adapter Board for LiPo charging Visit our FMA Cellpro Multi4 category to view all available accessories
- For Battery types: Lithium Polymer/Lithium Ion/Lithium Manganese (1s to 4s balanced and 2s unbalanced), A123 (LiFePO4) (1s to 4s balanced and 1s to 5s unbalanced), NiCd/NiMH (1s to 12s unbalanced), Pb (6v and 12v)
- Pack capacity: 5 mAh to 32Ah (charge time limited to max 8 hours)
- Input voltage: 10-16VDC, reverse polarity protected
- Input current: 1A to 5A, software limited, user adjustable using PC software
- Power conversion: DC/DC converter, 125 kHz, 90% efficiency
- Nominal Output Voltage: 1.58, 3.65, 4.10, and 4.20 volts per cell (user adjustable using CCS); 19V maximum
- Output battery charge current: Adjustable range 5mA to 4A, limited by 5A input current*
- Continuous max output power: 58W @ +12VDC input
- Voltage calibration: Cell voltage measurements are factory calibrated to a standard traceable to NIST; calibration is to +/- 6 mV
- Current calibration:Charge current is factory calibrated on a 4A standard; calibration is to +/- 1mA
- Measurement accuracy:
- Voltage resolution: 0.1mV
- Voltage tolerance: +/- 6mV
- Charge current: +/- 1%
- Capacity added to pack: +/- 1%
- Percent capacity (“Fuel”): +/- 20%
- Serial data output: 19.2kbps, 8 bits, 1 start bit, 1 stop bit, no parity
- Data integrity: Checksum, CRC checking
- Output battery connector: “Cellpro” compatible, JST PA series, 5 position
- LCD: 2 line, 16 character, light grey/blue backlit
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features:
- Selectable charge rates range 5mA to 4A
- Auto charge mode (AUTO 1C, 2C, 3C charge rates) available utilizing advanced fuel gauging technology
- Backlit Liquid Crystal Display
- High Impact ABS Plastic protective enclosure
- Multi-Chemistry, supports LiPoly, LiIon, LiFePO4, A123, LiMn, NiCd, NiMH, Pb)
- Supports 2-way P.C. Interface (FUIM3) which allows the charger to operate with the free Charge Control Software (CCS)
- Initiate charge at the charger or via remote control from the CCS. Graph all major operations when using CCS.
- Enhanced Internet Upgradable (IU) Charge Control Software (free download)
- IU Firmware support (free for the life of the product)
- Open Architecture presets allow for customization of any User Preset including show/hide presets on unit, preset name editing, up to 70 parameters control how presets are displayed and charging parameters associated with particular batteries and/or charging strategies. Unit includes 25 user preset banks pre-loaded for most major battery type/chemistries, plus 50 library presets.
- Basic preset parameters (select charger preset and choose current) may be edited at the charger, -or-
- Advanced editing of presets may be accomplished using the Charge Control Software
- Adapters available for all popular R/C battery brands
- Intuitive 1 button user interface
- Edit, save, and recall presets one at a time to your PC using the CCS
- Backup all 25 user programmable presets in the charger to your PC
- Share custom presets with your friends
- Edit, save, and recall custom fuel tables to improve the accuracy of AUTO charge modes. Custom fuel tables may be generated from 1C manual charge graphs of Li batteries, included with software upgrades over time, and/or shared with friends over the internet.
- Alter the individual charger displays to meet your needs. Change the order of any screen or hide screens from displaying. Set each preset to present the information you want the way you want it using the CCS.
- Support for non-balanced charge of A123 packs (up to full output voltage of the charger)
- Automatic Low voltage restore for recovering damaged or overdischarged packs
- Programmable options allow speaker ON/OFF or volume, LCD contrast, customized welcome screen, and much more
- Cold weather mode reduces end-charge voltage; parameters adjustable by customer including ON/OFF, end-charge voltage offset reduction, and temperature
- Support for non-balanced charge of 2s LiPo for small park flyer batteries.
- Unprecedented Accuracy
- Fuel Gauge Readout
- Unparalleled Safety
- Self Diagnostics
- Storage Charge Mode
- Safety Charge Mode
- Support for long battery extensions
|
|
|
|
|
|
|
|
|
